After purchasing asus rt n12, you have a question: how to set up local wifi network. To answer, you need to understand the features of connecting through this router. This is exactly what we will do now.

So, first of all, let's look at the connectors on the back panel of the equipment and connect the cables correctly. There are 5 special ports on the back of the router: 1 of them is for WAN, to which the main provider cable is connected, and the remaining 4 are for LAN type cables.

After connecting all cables, further configuration is best done with personal computer, having a direct connection to the equipment. Next, we move on to setting up the router itself.

IMPORTANT! To connect a desktop computer or laptop, a LAN cable is used, one end of which is connected to any LAN port on the router, and the other to the corresponding port on the network card of your personal computer or laptop.

This recommendation may seem funny and obvious to some, but still check the connection of the router to the outlet. And also make sure that the Internet connection is working and there are no problems with the provider. In addition, check that only the local network connection is active.

Initial router setup

We have already connected all the cables, checked the Internet connection and plugged the router into a power outlet. Now we need to learn how to configure the route. And this is done as follows:

IMPORTANT! We write “admin” if we have not yet changed the factory settings.

1. If you are setting up equipment for the first time and have logged in for the first time, automatic setup will start. With automatic setup, you only need to click on the “next” button and enter the required data.
2. Then the router will determine the type of Internet connection. If it is successfully determined, enter the password and username that you usually use to access the Internet.
3. Now you need to enter a personal name wireless network Wi-Fi and come up with a password for it.

If you cannot configure the equipment and establish correct operation using automatic settings, and the connection type was not detected automatically, you must make the settings manually.

Setting up a local network of various providers using a router

Internet settings from Beeline, Rostelecom and Dom.ru differ from each other. Next, we will consider the setup procedure for each provider.

First, let's look at Asus setup RT-N12 for the Beeline network: on the main router settings page (we accessed it through the browser address bar using the router’s IP address), click the “Internet” section. A window opens in front of us, where we fill in some lines, as shown in the illustration below. The main thing is to select L2TP in the connection type and tp.internet.beeline.ru in the VPN server item. We put ticks in two places, as in the figure.

After that, save the entered data by clicking “Ok”. If all items are checked correctly, after 20-30 seconds the connection to the Beeline network will be disconnected. Then, after a few seconds, the connection will be restored, and you will be able to work with various sites and other Internet resources. Also, the Wi-Fi network will be correctly displayed and work on all devices: smartphones, tablets, and so on.

If you use the services of Rostelecom or Dom.ru, then we configure the router in the same way, but only for home page In the router settings, in the “Internet” section, we indicate other data: in the connection type item, we indicate PPPoE, and not L2TP, as before. We also enter your unique username and password. The remaining points remain unchanged. The illustration below shows what a completed section looks like.

Setting up a wireless Wi-Fi network using the Asus RT-N12 router

Open the menu and select “Wireless Network”. Next, fill in a number of points:

• The first item is the SSID, or the name of the wireless network. The name of your network will appear in the Wi-Fi search list on all devices within range of the network. The name is written in English letters.
• In the “Authentication” section, select WPA2-Personal.
• Next, enter the password in the “WPA Pre-Shared Key” section. The password must consist of at least 8 digits.
• Save the settings.

The figure below shows what the “Wireless Network” section looks like.

Setting up a local network via asus rt n12

So, we figured out how to connect and configure the asus rt n12 router. Now let's look at how to set up a local wifi network via asus rt n12.

Go to the “Local Network” section.

We change the router address, which was set by default, do this in the “LAN IP address” tab.

Enter the IP address of your local network and click “Apply”. After this, the equipment will work for your local network.

To set up an ASUS router, you need to connect. Then, in your browser, follow the link - 192.168.1.1 . If you have not configured the device before, you will see Quick Setup Wizard. If you need a login and password, then in both fields by default we type admin(should be checked with providers). The ASUS control panel will be displayed.

Basic settings

The panel consists of general and additional settings. Available opportunity viewing the network map, enabling guest Internet, traffic control, and parental controls. In the additional section Wi-Fi is regulated and configured firewall.

To check if you are connected, you can go to the “ Quick setup networks" Then select " Check your connection" And " Go" In the window that appears, enter your username and password. Click " Next" Then in the section " Setting up the router» fill in the specified name (SSID) and network key (to connect to the network).

Click " Apply" It will begin. Then a network with the name you specified will appear in the Wi-Fi list. We connect to the device using the specified access key and return to this section. In the window with connection information, click “ Next».

In most cases, the Internet should already be working, but if your provider does not support the technology AutoIP, That tune Wi-Fi follows on its own. In this case, after checking the connection, the section “ Internet Settings».

Next in the proposed list choose the connection technology used by your provider. Then in the window that appears you will need to enter login And password, which were provided by the provider in the contract. All information should be clarified with him if any problems arise. It may be necessary further enter any other parameters that must also be taken into account (service name, IP address, etc.). Afterwards you need to do all the same steps as described above.

Wi-Fi Settings

On the main tab there is always an additional option tune Your Wi-Fi. For example, in the section " Internet" Can change type of WAN connection, that is, if the provider has changed the connection technology, you can switch it. In the section " Network map» there is a possibility change key to connect Wi-Fi, as well as your username (be sure to click " Apply"). Can be customized guest network(not recommended if you need to control Internet traffic) and impose parental controls, if necessary save child from an unwanted resource.

You can also change access key to the control panel of your router. To do this, go to " Administration", hereinafter - " System" Enter your new password and click " Apply" for it to take effect. The remaining sections mainly contain additional settings wireless and local Wi-Fi, which can be configured at your discretion.

How to reset a router

If you forgot your wireless Wi-Fi password and other devices were not connected, try logging into control Panel on cable and view it there. But if this is not possible, it is recommended reset router to default settings.

There is a special button on the back of the router for this purpose. Press and hold it about 15 seconds until the WPS indicator starts blinking. The access key will be reset, you must follow all the steps described in the article above. To avoid such situations, when connecting on your computer, you should always check the “ Connect automatically" Then the Wi-Fi login will be done using autofill.

How to connect WiFi router Asus?

Nowadays, many people install a router with wireless Internet at home. Usually a technician comes for installation and does all the work of drawing the necessary wires, connecting the router and configuring it. However, it happens that installing and configuring a router is a paid service and the apartment owner is not ready to pay extra money for it. In this case he wants to connect Wi-Fi router independently, but often does not know how.

Let's look together at how to connect and configure an Asus Wi-Fi router yourself.

How to connect an Asus router

All routers today are made basically according to the same standard. Therefore, connecting the router will not be difficult. To do this you need:

1. Connect the wire from the provider to the WAN port to the router. You just need to run a wire from the front door to the router.
2. Then we connect the wire from the LAN port of the router to the computer, so that later you can configure the router.
3. We connect the router to the power supply.

The remaining LAN ports can be used to connect other computers, laptops, printers and any equipment that can work with the router. After turning on the router, a wireless network will appear, but you still need to configure the router.

How to configure an Asus router correctly

Having connected the router to the computer via a wire, we begin setting up the router. However, if the computer does not see the connected router, then you must first install the necessary drivers, which can be found on the router disk or download drivers for the network card from the Internet.

After this, we begin the setup:

1. Open any browser and enter address bar"192.168.1.1." The router setup menu will open.
2. In the window, enter your username and password to get to the router menu. You can view your login and password in the documentation for the router or on the back cover of the router itself. Typically, the username and password are the word “admin”. If, after entering the correct username and password, nothing happens, then you can reset all the router settings to factory settings. To do this, press the “reset” button on the router for ten seconds.
3. The router menu will have several sections. In the provider data section, you must enter all the data that the provider provided for connection. You can find them in the documentation, on the provider’s website, or find out more by calling the provider. However, usually the settings are determined automatically by the router and there is no such need.
4. In the wireless settings section Wi-Fi networks you need to set a new network name and a new password that only you will know. This is done to prevent neighbors from using your Internet.
5. You can also change the login and password to access the settings of the router in the router settings.
6. Save the new values ​​and reboot the router.

Now you can use the Asus router.

Before you start setting up the router, you will need to prepare your computer for further setup, as well as clarify some of the connection parameters. How to do this is described in detail in our instructions: ! When the computer is ready, we proceed directly to setting up the router.

Connecting the router:

• We connect the router to the network using the included adapter
• We leave the operator cable “on the floor”
• Connect with the cable included in the kit network cards router ( LAN 1) and computer ( Ethernet) (Rice. 1)

Wait until the lights on the router light up power diodes (PWR), active first port (LAN1) And WLAN (AIR), although it happens that the latter is disabled in the router settings.

Setting up the ASUS RT-N10 router

2. In the address bar we indicate the IP address of the router: http://192.168.1.1
After entering the address, an authorization window will appear on the screen to access the router settings ( Rice. 5). To enter the configurator, enter:

• login – admin
• password - admin

3. Not For experienced users, the system will offer an attempt to set up an automatic connection through the configurator; to do this, just click “ Next": Rice. 6

4. If your provider provides the Protocol - Static IP address and exactly 192.168.1.1 (how to find out what protocol you have is described in detail in our instructions: Preparing the PC before setting up a Wi-Fi router), which coincides with the router’s IP address, in the “ LAN", in the tab LAN IP address, you should change the router's IP address to 192.168.100.1 , then press “ Apply"and reboot the router. We also reboot the computer and re-enter the router through the browser, but through a new IP address ( Rice. 7):

5. If the protocol is different from the above or your operator has a different IP address, skip Point 4.:

6. If auto-tuning does not complete successfully, go to the “ WAN", where from the list we select the Protocol of your operator ( PPPoE, PPTP or L2TP):

7. Depending on the provider, IP addresses and DNS are provided automatically or must be entered manually. We will also learn these parameters from the instructions: Preparing the PC before setting up a Wi-Fi router. We indicate in the window username And password, according to the requirements of the operator, and binding, if necessary, to the physical address:

8. After applying and rebooting the router, enter the settings section Wireless network.

According to the above figure, you should specify the parameters of the future Wi-Fi network:

• “SSID” – you can leave the network name or change it to your preferred one;
• “Wireless network mode” - we also recommend choosing a specific one; if the computer does not support Wi-Fi class N (indicated in its specification), select the mode "g Only". Mixed modes are not recommended "...mixed";
• “Channel” - instead of “Auto” we recommend choosing a specific one from 1 to 13 (for example 6 or 9);
• “Authentication method” – (protecting your network - will help protect home network from connecting inquisitive neighborsJ) – we recommend choosing WPA-Personal– a reliable encryption method that will ensure your security. This mode is used for maximum data exchange speed. WEP encryption reduces the speed of network access, and the WPA2 type is not supported by all devices that will connect to the router;
• “WPA encryption” - for the WPA verification method, select TKIP;
• "WPA Pre-Shared Key" is a password that protects your network. It must be entered if the Authentication Method from the previous paragraph is specified - you will have to come up with a password yourself and enter it in the appropriate field, remember it and write it down in your notebook.

Recently, wireless networks have become an urgent need in many homes. This is especially true for those who use laptops, tablets, smartphones and other portable devices to access the Internet. Agree to burden these devices with a wire, somehow... at least inconvenient. And it will be convenient for you if you sit comfortably in your favorite chair or on the sofa and from there surf the Internet from your tablet or laptop. In order for all this splendor to come to life, you will need a Wi-Fi router and knowledge of how to set it up. There are a lot of routers nowadays, but among them the most popular are routers from ASUS, TP-LINK, D-Link, Linksys and ZyXEL. In this lesson you will learn how to set up an Asus router.

1. Step

Connect the router as shown in the figure. The yellow WAN cable is the cable that brings the Internet into your home. LAN are ports for connecting your computers using a cable.

2. Step

Go to your computer's network settings for the TCP/IP protocol. This can be done in the menu "START > Settings > Control Panel > Network connections" . In the window that opens, click right click mouse on the active connection and select "Properties".

In the network settings window, select "Internet Protocol TCP/IP" and click the "Properties" button

In the TCP/IP protocol settings window, select “Obtain an IP address automatically.”

3. Step

Launch your browser and enter in the address bar: http://192.168.1.1 (this address is usually set by default on Asus routers). Press Enter and enter your login and password to access the administrative panel of the router (by default, login: admin, password: admin).

If the login and password request window does not open, or the admin login does not work, then you will need to reset the router settings to factory settings; usually for this purpose, there is a special reset button on the router case. If this is not observed, then read the device instructions.

4. Step

In the admin panel, click on the item "IP config" and select "WAN Connection Type" How "Static IP:"

5. Step

Enter your network settings ( IP Address, netmask, Gateway, DNS) in the appropriate fields:

6. Step

Now go to the menu item " Wireless" select " Interface", select WPA/WPA2 encryption and enter a password to protect your wireless network from unauthorized access.

7. Step

We save all our settings" Save settings"

8. Step

Now on your computer (laptop) in the list of found WI-FI devices, select your Asus device and connect to it. Enter the password you created in step 6.

The setup is complete.

(11 Votes)

---